Engineering

Write the differential equation for steady-state diffusion and homogeneous chemical reaction at constant reaction rate K in a cylindrical rod.

Transport phenomena Poly (vinyl chloride), PVC, is a common polymer used for fluid pipes and many consumer products, such as inflatable mattresses. It degrades at high temperatures and forms hydrochloric acid, a highly corrosive acid: (C2113COn —, (C2112)7, + HCl This occurs at a constant rate K, which is independent of HC1 concentration. Consider a […]

Using the information provided, draw the projections of AB and shows its inclinations with the H.P. and V.P.

ASSIGNMENT i) Solve all questions. ii) All dimensions are in mm. iii) Use the first angle method of projection. iv) Assume a suitable dimension if it is necessary. v) Retain all construction lines. vi) Line work should be in such a way that the drawings are neat and clear while scanning. Solve any One Question […]

Discuss how the Deming Cycle impact Six Sigma and other forms of continuous improvement. Provide examples.

ASSIGNMENT Deming was largely responsible for bringing statistical thinking and methods after WWII. Discuss how the Deming Cycle impact Six Sigma and other forms of continuous improvement. Provide examples. Essential Activities: Watching the videos, https://www.youtube.com/watch?v=hUHiDPKXcw4&ab_channel=ClintStevenson https://www.youtube.com/watch?v=31m2WePfqIc&ab_channel=KrishnamurtyPammi https://www.youtube.com/watch?v=ilDAYBR5sQU&ab_channel=ProjectManager Notes: This paper must be formatted in APA Style 7th edition. No Plagiarism.  

Based on the figure below, which tasks is P dependent on? Show all your work to support your answer (i.e., must show any calculation you performed, and circle your final answer).

ASSIGNMENT Based on the figure below, which tasks is P dependent on? (1 pt) N O Q all of these none of these What is the slack time for task R? (1 pt) Why is this the slack time? Show all your work to support your answer (i.e., must show any calculation you performed, and […]

Based on his description of SISOS, do you think agile SDLC models are appropriate for developing these types of systems?

A View of 20th and 21st Century Software Engineering “Barry Boehm in his article “A View of 20th and 21st Century Software Engineering” discusses software-intensive systems of systems (SISOS). 7 pts total a) Based on his description of SISOS, do you think agile SDLC models are appropriate for developing these types of systems? (2 pts) […]

Based on the ACM/IEEE Software Engineering Code of Ethics, how would you approach this situation if you were assigned to develop this tracking system. Discuss two ethical principles in the code of ethics.

ASSIGNMENT To help counter terrorism, many countries are planning or have developed computer systems that track large numbers of their citizens and their actions. (8 pts total) a) Discuss the dual-use dilemma in this context. (3pts) What is dual-use dilemma? How does dual-use dilemma apply to this context? (3 sentences max) b) Based on the […]

Design a second-order low-pass Butterworth filter having a gain of 10 and a corner frequency at 1k rad/s. Show your complete work and the LTspice schematic and simulation result.

Assignment Design a second-order low-pass Butterworth filter having a gain of 10 and a corner frequency at 1k rad/s. Show your complete work and the LTspice schematic and simulation result. You must submit the hand calculation written neatly, and the LTspice schematic and simulation results.

If C,n = 0 , Apply Kirchhoff s laws to the LPM circuit and derive the ODE relationship between Pa and P. Draw a block diagram to represent the ODE derived in a.

ASSIGNMENT In the figure, R., and R„, denote the flow resistances of the stenosis and the microcirculation, respectively. Cm denotes the compliance of the microcirculation. Pa and Pd denote the aortic pressure and the distal pressure from the stenosis, respectively. The terminal pressure Po is assumed to be zero. Qin denotes the inlet blood flowrate […]

Why an engineer has to draw shear force diagram and bending moment diagram for a beam. Provide a sketch for above explanation.

Mechanic Assignment Q1 a.Why an engineer has to draw shear force diagram and bending moment diagram for a beam. Provide a sketch for above explanation. (0.5 Marks) [Answer in your own words] Q1 b. Draw a simply supported beam with roller support. Mark the type of loads that can be applied on the beam and […]

Design a PID controller by using Ziegler-Nichols step response method. Compare the controllers in calculating root mean square error (MUSE).

ASSIGNMENT 1 Problem A chemical reaction, takes place in a continuous stirred tank moor (CSTR) at VC. The reactant A has 95% purity and temperature is less than TsC. Whereas reactant B has 85% purity and temperature is more than re. The product is separated to component C and D. at temperature D.C. The prom. […]

Scroll to top